Marvel Schebler type Carburetor for C113 gas engines. Includes carb mounting gasket and mounting studs are 2 3/8" CTC. Part Reference Numbers: 352376R92;354184R93;355485R91;373957R91;52499DB;69401D;TSX156;TSX157;TSX319 Fits Models: A; AV; B; BN; C; SUPER A; SUPER C If you get this carb and do not like it, you can return it within 30 days. If it comes into contact with fuel, it becomes NOT RETURNABLE. If for any reason, this carb smells like fuel, it is NOT Returnable. IF YOU DECIDE TO USE THIS CARB, FLUSH OUT THE ENTIRE FUEL SYSTEM. PUT IN A NEW FUEL FILTER AND CLEAN OUT THE FUEL PUMP BOWL. THE SMALLEST AMOUNT OF DEBRIS IN THE FUEL LINES CAN DISABLE YOUR CARB. NO CARB THAT HAS COME INTO CONTACT WITH FUEL IS RETURNABLE.

Specifications 1/4" NPT Fuel Inlet All Fuel tractors will have (2) - 5/16" compression outlets, where gas only tractors will have only (1) outlet. Includes (2) fuel line fittings: 5/16" Compression Fittings. Fuel lines thread directly into the sediment bowl housing. This sediment bowl is designed for tractors with 2 fuel tanks. Model Note Equipment Information H up to SN: 50865 HV up to SN: 50865 M up to SN: 24214 MV up to SN: 24214 O4 up to SN: 1129 McCormick Deering O6 up to SN: 1316 McCormick Deering W30 Fits if you change the fuel line fittings, up to SN: 28534 McCormick Deering W4 up to SN: 1129 McCormick Deering W40 Fits if you change the fuel line fittings, all gas McCormick Deering W6 up to SN: 1316 McCormick Deering 10-20 Fits if you change the fuel line fittings, SN: KC172094 and up McCormick Deering 15-30 Fits if you change the fuel line fittings, SN: 45513 to 142419 McCormick Deering 22-36 Fits if you change the fuel line fittings McCormick Deering F12 Fits if you change the fuel line fittings, SN: 501 to 3034 F20 Fits if you change the fuel line fittings, up to SN: 93064 F30 Fits if you change the fuel line fittings, up to SN: 25889 Regular Fits if you change the fuel line fittings, SN: 87182 and up McCormick Deering

Specifications Repair kit includes: Needle and seat Float lever pin Gaskets Graphite packing (for main adjusting needle) Idle adjusting spring Idle adjusting needle Throttle shaft Felt packing (throttle shaft seal) Instructions Note: The instruction sheet and diagram show parts that are not included in this kit. These parts are shown for reassembly purposes only. O12 with IHC carburetor O14 with IHC carburetor W12 with IHC carburetor W14 with IHC carburetor F12 with IHC carburetor F14

BASIC CARBURETOR REPAIR KIT --- KIT CONTAINS: THROTTLE SHAFT, NEEDLE & SEAT, FLOAT LEVER PIN, CHOKE & THROTTLE SHAFT SEALS, NEEDLE VALVE, ADJUSTMENT SCREW, GASKETS & INSTRUCTIONS. --- Carburetor Manufacturer #: 50981DA, 50981DB, 50981DC --- International Applications: H, HV, 4 SERIES

Specifications Kit includes: throttle shaft (original style with cast iron arm) needle and seat float lever pin choke and throttle shaft seal needle valve idle adjustment screw with graphite packing friction ball gaskets and instructions 560 656 660 706 756 766 806 826 856

Specifications New Zenith carburetor, not rebuilt 2-11/16" center-to-center mounting studs 1.299" throttle bore 3/8" fuel inlet 2.040" housing outside diameter for air cleaner hose Zenith Carburetor 14996A Note: Carburetors are limited to replacement only. Warranty void / replacement not offered if rust, dirt, etc. is found in the carburetor or if it has been taken apart. 454 464 504 544 574 656 666 throttle shaft and choke shaft must be disassembled and remounted on the opposite side 674 686

Carburetor Float For Farmall: 2400, 2500A, 2500B, 2504, 2544, 2656, 3514, 454, 464, 504, 544, 574, 656, 666, 674, 686. Replaces International PN#: 381962r1 Picture Is For Reference Only Marvel Scheibler Carburetors: TSX1001, TSX181, TSX221, TSX245, TSX296, TSX332, TSX360, TSX374, TSX397, TSX413, TSX414, TSX436, TSX464, TSX466, TSX475, TSX492, TSX505, TSX505A, TSX506, TSX526, TSX528, TSX530, TSX561, TSX562, TSX563, TSX575, TSX582, TSX592, TSX596, TSX602, TSX610, TSX615, TSX633, TSX639, TSX641, TSX645, TSX648, TSX662, TSX678, TSX688, TSX689, TSX695, TSX704, TSX711, TSX713, TSX719, TSX721, TSX725, TSX732, TSX737, TSX738, TSX755, TSX756, TSX757, TSX768, TSX769, TSX772, TSX773, TSX774, TSX775, TSX777, TSX784, TSX788, TSX791, TSX792, TSX797, TSX798, TSX799, TSX800, TSX801, TSX806, TSX808, TSX810, TSX811, TSX813, TSX814, TSX816, TSX819, TSX825, TSX835, TSX836, TSX840, TSX843, TSX846, TSX853, TSX854, TSX856, TSX857, TSX869, TSX871, TSX877, TSX878, TSX881, TSX883, TSX884, TSX885, TSX886, TSX888, TSX889, TSX892, TSX892S, TSX893, TSX894, TSX895, TSX897, TSX898, TSX899, TSX900, TSX902, TSX903, TSX904, TSX904SL, TSX905, TSX905-1, TSX905SL, TSX906, TSX906SL, TSX907, TSX907SL, TSX908, TSX908SL, TSX911, TSX917, TSX920, TSX920SL, TSX921, TSX921SL, TSX922, TSX922SL, TSX923, TSX923SL, TSX925, TSX927, TSX928, TSX932, TSX932SL, TSX933, TSX934, TSX936, TSX938, TSX938SL, TSX939, TSX940, TSX941, TSX941SL, TSX944SL, TSX945SL, TSX946, TSX947SL, TSX950, TSX952, TSX959, TSX966, TSX97, TSX970, TSX972, TSX973, TSX974, TSX975, TSX977, TSX980, TSX984SL, TSX985SL, TSX988, TSX989, TSX992, TSX993, TSX994, TSX997, TSX998, TSXU835, TSXU836, TSXU840, TSXU908SL, TSXU963

Other Application Info Fits all H, I4, O4 & W4 series except Super I4 H HV O4 W4

Specifications 5-piece gasket kit For small bowl Marvel Schebler carburetors 4-5/16" overall length of the bowl gasket A some AV some Super A some Super AV some Super AV-1 some B some BN some C some Super C some T340 some Crawler T5 some Crawler 100 some 130 some 140 some 200 some 230 some 240 some 330 some 340 some 404 some 424 some early 444 some early 504

Specifications Fits same as FDS212 carburetor kit 5" length bowl gasket Hydro 70 Some 454 Some 464 Some 504 Some 544 Some 574 Some 656 Some 666 Some 674 Some 686

Specifications 0.3125 Hex 1.777" long 0.122" tube 0.060" hole I.D. 4 discharge holes Model Note Equipment Information Cub with IH Carburetor 1947 - 1956 small bore

Specifications For carburetors listed using throttle body 8557D, 8867DX. Steel The throttle shaft is also made like the original and has a steel governor drive keyway (not a plastic drive keyway). 3.314" long Model Note Equipment Information Super H Super HV I9 M Super M MTA MV Super MV O6 OS4 OS6 T6 Super W6 Super W6TA W6 W6TA W9 WR9 WR9S 300 distillate or kerosene Farmall Rowcrop 350 distillate or kerosene Farmall Rowcrop 400 distillate or kerosene W400 Wheatland 450 distillate or kerosene W450 Wheatland 600 650

Specifications 1.553" long 1.425" O.D. for Throttle Body 1.610" O.D. Shoulder 1.487" O.D. for Fuel Bowl. M gas or LP Super M gas or LP Super MTA gas or LP MV gas or LP Super MV gas or LP O6 gas or LP OS6 gas or LP Super W6 gas or LP Super W6TA gas or LP W6 gas or LP 400 gas or LP W400 gas or LP 450 gas or LP W450 gas or LP 460 gas or LP 560 gas or LP 660 gas or LP 706 gas or LP

This is a NEW carburetor, not rebuilt Mounting studs are 2-11/16" center to center Governor linkage pattern is 1-3/4" center to center The throttle body throat size is 1-7/16" diameter The choke air horn (air inlet) measures 2-1/4" outside diameter M MV O6 OS6 W6

Quad Ring: Filter Housing Seal 3.440" O.D. 3.145" I.D. 0.125" Thick

COMPLETE CARBURETOR REPAIR KIT (ZENITH) MAKE SURE THAT YOUR CARBURETOR MANUFACTURER NUMBER IS IN THE LIST THIS FITS!!!!! KIT CONTAINS: CHOKE & THROTTLE SHAFTS, NEEDLE & SEAT VALVE, FLOAT LEVER PIN, MISCELLANEOUS PLUGS & SCREWS, THROTTLE SHAFT SEALS & GASKETS Carburetor Manufacturer #: 10514A International Applications: A, B, SUPER A, AV

Specifications CAV style filter = lines come in from sides (not from top like a Simms filter) ESN = Engine Serial Number SN = Serial Number 574 584 674 684 784 785 884

Specifications Many Carter carburetors are missing the tag and can not be identified. This kit has all five bowl gasket variations along with both style needles and seats fitting all Carter carburetors. Super A Super AV C Super C 100 130 140 200 230

Specifications Kit includes: Needle and seat gaskets and instructions (includes extra gaskets allowing it to fit all the British Zenith carburetors used on the below listed models B-250 with BC144 engine, using British Zenith carb numbers VN, VNN, VNP, 3044193R92, C1751, C1759, 3106595R91, 3063945R91 B-275 with BC144 engine, using British Zenith carb numbers VN, VNN, VNP, 3044193R92, C1751, C1759, 3106595R91, 3063945R91 B-414 with BC144 engine, using British Zenith carb numbers VN, VNN, VNP, 3044193R92, C1751, C1759, 3106595R91, 3063945R91 354 with BC144 engine, using British Zenith carb numbers VN, VNN, VNP, 3044193R92, C1751, C1759, 3106595R91, 3063945R91 444

Specifications Before ordering, please make sure to double check that your carburetor number is listed. Carburetor Numbers TSX1000, TSX662, TSX769, TSX813, TSX857, TSX966, TSX970, TSX972, TSX973, TSX977, TSX988, TSX989, TSX997, TSX998,

Specifications 7/16" - 24 special fine thread seat Model Note Equipment Information Super A Super AV 100 130 with Aluminum upper carburetor body 140 200 181578M91 182748M91 184458M91 373957R91 373959R91 373961R91 373962R91 UT UT2257S UT2612S 0-1146, Fits carbs with aluminum upper throttle body # 0-1177, Fits carbs with aluminum upper throttle body # 0-1178, Fits carbs with aluminum upper throttle body # 0-1396, Fits carbs with aluminum upper throttle body # 0-1397, Fits carbs with aluminum upper throttle body #

Economy Zenith Carburetor Repair Kit In Stock At our Michigan warehouse ABC1348 $20.95 Sugg. Retail: $27.99 Min. Quantity Max. Quantity Price 1 4 $20.95 5 $16.00 - 1 economystandardpremiumtruck Other Customers Also Bought Specifications Needle & Seat #31-646 (3/8 thread) Float lever pin Seal Gaskets Instructions INCLUDES PARTS SHOWN IN PICTURE, INSTRUCTION SHEET

Specifications This is a NEW carburetor, not rebuilt. Mounting studs are 2-3/8" center to center. The throttle body throat size is 1-3/16" diameter. The choke air horn (air inlet) measures 1-3/4" OD. The carburetor mounting gasket is included. I4 H HV O4 OS4 W4

3-1/2" outside diameter 3/4" inside diameter 2.85" tall

Specifications 1" center hole inside diameter 2" tall 3.689" gasket mounting flange outside diameter 3.300" bowl outside diameter Flat bottom with squared edge Gasket is not included Hydro 84 diesels with original CAV filter 354 diesels with original CAV filter 384 diesels with original CAV filter 584 both with engine SN: 318210 and up diesels with original CAV filter 784 both with engine SN: 120521 and up diesels with original CAV filter 785 both with engine SN: 120521 and up diesels with original CAV filter 884

Specifications 0.710" I.D. bottom hole 1.600" tall 3.660" O.D. 3.310" I.D. (where filter sits) Rounded bottom Gasket not included Fits CAV type filters #296 and #796 454 ''some'' 464 ''some'' 484 ''some'' 544 ''some'' 584 ''some'' 684 ''some'' 784 ''some'' 826 both with BR pump ''some'' 884