Part Reference Numbers: A137187 Fits Models: 580B INDUST/CONST

Part Reference Numbers: D84179 Fits Models: 480U INDUST/CONST

Part Reference Numbers: 366441A1 Fits Models: 3220 TRACTOR; 3230 TRACTOR; 380B INDUST/CONST; 385 TRACTOR; 395 TRACTOR; 4210 TRACTOR; 4220 TRACTOR; 4230 TRACTOR; 4240 TRACTOR; 485; 485XL TRACTOR; 495 INDUST/CONST; 495XL INDUST/CONST; 585XL TRACTOR; 595 TRACTOR; 595XL TRACTOR; 685; 685XL TRACTOR; 695 TRACTOR; 695XL; 785; 785XL; 795; 795XL; 885; 885XL; 995; 995XL; C100; C50; C60; C70; C80; C90

Models without relief valve, 385 (SN

Steering motor with roll pin shaft. Part Reference Numbers: 1263446C91 Fits Models: 1086 TRACTOR; 1486 TRACTOR; 1586 TRACTOR; 5088 COMBINE; 5288 TRACTOR; 5488 TRACTOR; 886; 986; HYDRO 186

Steering motor with splined and threaded shaft. The ports are approximately 45 degrees from the original equipment modification or the original steel lines. Part Reference Numbers: 70111C94 Fits Models: 1066 TRACTOR; 1466; 1468 TRACTOR; 1566 TRACTOR; 1568 TRACTOR; 766 TRACTOR; 966; HYDRO 100

This unit has 5 hydraulic lines and 3 mounting studs on the bottom of valve. Part Reference Numbers: D91505 Fits Models: 580D INDUST/CONST; 580E INDUST/CONST

Used on Case Forklift models Part Reference Numbers: D90752 Fits Models: 584C INDUST/CONST; 584D INDUST/CONST; 585C INDUST/CONST; 585D INDUST/CONST; 586C INDUST/CONST; 586D INDUST/CONST

Part Reference Numbers: D89898 Fits Models: 480B INDUST/CONST; 480C INDUST/CONST; 580B INDUST/CONST; 580C INDUST/CONST

POWER STEERING PRIORITY FLOW CONTROL VALVE --- ELIMINATES BELT DRIVEN PUMP, PULLEYS & BRACKETS. ENABLES YOU TO USE YOUR LIVE HYDRAULIC PUMP TO OPERATE THE POWER STEERING. --- MUST BE USED W/ LIVE HYD. --- 3/4" INLET & RETURN --- 1/2" PRESSURE PORT -- PRE SET AT 1500 PSI, ADJUST TO YOUR APPLICA --- International Applications: H, SUPER H, HV, SUPER HV, M, SUPER M, MD, MTA, MV, MDV, SUPER MV, SUPER MDV, W4, W6, W9, WD6, SUPER W6, SUPER W4, SUPER W6, SUPER W9, WR9, WD9, SUPER W6TA, SUPER W6TA DSL, SUPER WDR9, 300, 350, 400, 450

TORQUE GENERATOR --- HEAVY DUTY IF ONLY USING THIS PIECE, ALSO NEED PORT BLOCK, IHS673 FOR WHEN A FRONT LOADER IS USED TORQUE OUTPUT AT 1000 PSI = 1100 IN LBS RATED OPERATING PRESSURE = 1000 PSI MAX. OPERATING SPEED AT 3 GPM = 65 RPM RECOMMENDED FLUID INPUT = 3 TO 4 GPM 7 --- International Applications: H, HV, SUPER H, SUPER HV, M, MD, MV, MDV, SUPER M, SUPER MD, SUPER MV, SUPER MDV, MTA & OTHER MODELS USING 7/8"" DIAMETER STEERING SHAFTS